Usage examples of "V weld" in English with translation to Russian

<>
If he starts screwing with us, we just ship him back to Ely and weld his cage shut. Если он начнёт вешать нам лапшу на уши, мы просто отошлём его обратно в Эли и заварим дверь его клетки.
I can reroute the primary initiator, weld the dampening vents, and that might give us enough power to leave the atmosphere. Можно перенаправить первичное зажигание, заварить выхлопные клапаны, тогда нам может хватить мощности, чтобы покинуть атмосферу.
We moved the ballast over to port side, so that we could weld it dry on starboard. Мы передвинули балласт к левому борту, чтобы мы смогли сварить насухо на правом борту.
Dylan weld, 36, art dealer. Дилан Уэлд, 36 лет, арт-дилер.
Section three weld scanners are temporarily offline. Сварочные сканеры третьего цеха временно не работают.
I can weld better than her an 'all. Сварочным аппаратом я работаю получше, чем она.
I weld stuff and I'm, like, you flip it on and off. Я умею сваривать, потом там просто включаешь и выключаешь.
There's space to experiment and to weld and to test things. Здесь можно свободно экспериментировать, объединять и тестировать разные варианты.
And what you do is you put it together in three layers, you weld it around the edge, and then you inflate it. Что мы делаем - кладем его в три слоя, спаиваем по краям и затем надуваем.
One tensile test perpendicular to the longitudinal weld; одно испытание на растяжение- перпендикулярно продольному сварному соединению;
The scope of the inspections referred to in 6.8.2.1.23 for weld beads was not clear where the connections were concerned. Охват проверок сварных швов, указанных в пункте 6.8.2.1.23, не ясен в том, что касается мест удара.
Test pieces from containers with one circumferential weld only (two sections) shall be taken from the places shown in appendix 2, Figure 1. Испытываемые детали баллонов, имеющие лишь один периферийный сварной шов (двухсекционные), должны быть взяты из тех мест, которые указаны на рис. 1 в добавлении 2.
bend test on a circumferential weld, the inner surface in tension испытание на изгиб по кольцевому сварному соединению, напряжение на внутренней поверхности
For the lower part of each shell at least 20 % of the length of each circumferential and longitudinal weld shall, together with all nozzle welds and any repair or ground areas, be inspected.”. В нижней части каждого корпуса должны проверяться не менее 20 % длины каждого кольцевого и продольного сварного шва, а также все сварные швы патрубков и все места, где производились ремонт или полирование ".
three test-pieces from the centre of the weld; три образца в центре сварного шва;
bend test on a longitudinal weld, the inner surface in tension испытание на изгиб по продольному сварному соединению, напряжение на внутренней поверхности
As already mentioned in the report of the working group's last meeting, the scope of the weld seam inspections set out in 6.8.2.1.23 is not clear with regard to the connections. Как уже упоминалось в докладе о работе последнего совещания Рабочей группы, охват проверок сварных швов, о которых говорится в пункте 6.8.2.1.23, неясен в том, что касается стыков.
For welds, the average value obtained from the three test-pieces taken at the centre of the weld shall not be below the minimum value of 34 J/cm2; not more than one of the individual values may be below the minimum value and then not below 24 J/cm2. Для сварных швов средние результаты, полученные на трех образцах, вырезанных в центре сварки, не должны быть меньше минимального значения 34 Дж/см2; не более одного значения может быть ниже минимальной величины, не будучи при этом меньше 24 Дж/см2.
One bend test on the circumferential weld, the outer surface in tension; and одно испытание на изгиб по кольцевому сварному соединению, напряжение на внешней поверхности; и
bend test on a longitudinal weld, the outer surface in tension испытание на изгиб по продольному сварному соединению, напряжение на внешней поверхности
Examples of word usage in different contexts are provided solely for linguistic purposes, i.e. to study word usage in a sentence in one language and how they can be translated into another. All samples are automatically collected from a variety of publicly available open sources using bilingual search technologies.
If you find a spelling, punctuation or any other error in the original or translation, use the "Report a problem" option or write to us.

What is translation in context on PROMT.One

The “Contexts” section on PROMT.One is your translation-in-context tool that helps you find real examples of how words and phrases are used. Just enter a word and the service will show its translation in context — sentences from bilingual sources where this word is used together with its translation into the target language. This helps you understand subtle shades of meaning and correct usage in speech, whether it is a rare term or a common everyday phrase.

Millions of usage examples from real texts

Millions of translation examples are collected automatically from already translated texts: documents, websites, books, movie dialogues and more. Thanks to this, you can see a word in different situations — from formal business style to everyday colloquial speech. For convenience, the results can be filtered by a specific translation or topic, and you can also search within the examples found to quickly focus on the context you need.

How translation in context helps you learn a language

By using the “Contexts” section, you can effectively expand your vocabulary. The service clearly shows how idioms, phrasal verbs and polysemantic words are translated in different contexts. This makes language learning easier: you remember new words together with their real usage and immediately see correct translations in authentic, living language. Take advantage of context-based translation on PROMT.One — learning a language becomes easier and more engaging!