Exemplos de uso de "sheet metal" em inglês

<>
It's a wall of sheet metal. Стена из листового металла.
Nothing I can't tell you about sheet metal, screws and surface plugs. Я вряд ли что расскажу тебе о листовой стали, винтах и штепсельных вилках.
It even contains a powerful force that can tear through sheet metal. В ней присутствует мощная сила, которая может пробить даже листовой металл.
A sheet metal shield to protect the propane flame from side winds. кожух из листового металла для защиты пламени пропана от боковых ветров.
This can be fabricated from approximately 0.5 mm thick galvanised sheet metal. Может изготовляться из листового металла с гальваническим покрытием толщиной 0,5 мм.
I didn't want to give up my sheet metal job, so I tried to do both jobs and finish middle school. Я не хотел бросать работу с листовым металлом, так что я попытался делать обе и окончить среднюю школу.
Although NHTSA did not experience penetration of door sheet metal from the loading plates, we recognized that without rounded edges on the plates, this might be a problem. И хотя НАБД не сталкивалась со случаями пробивания листового металла двери пластинами передачи усилия, мы признали, что такая проблема может возникнуть, если не закруглить края этих пластин.
The sun beats on the sheet metal of the roof. Солнце раскалило жестяную кровлю.
Ball-peen's more for hammering out dents in sheet metal, not for close tolerance phone repair. Этот молоток больше подходит для забивания гвоздей в фанеру, но не для сложного ремонта телефона.
Ed's pa staked us to a starter home in suburban Tempe and I got a job drilling holes in sheet metal. Папа Эд подкинул нам домик в пригороде Темпе и я устроился на работу сверлить дырки в листах металла.
For example, a sheet metal press may have the “Aluminum sheet press” capability assigned and have a grade of 50, whereas an older sheet metal press would have the same capability assigned, but the older sheet metal press can only manage a grade of 30. Например, для пресса для листовой штамповки может быть назначена возможность "Пресс для штамповки алюминиевых листов" и уровень 50, в то время как более старого пресса для листовой штамповки будет назначена та же возможность, но с уровнем 30.
In Sheet Metal Workers, Paradise and Johnson, all three affirmative action programmes were accepted, because their purpose was to remedy intentional discrimination practiced in the past against the African American population by the New York syndicate of metalworkers, the police corps of Alabama and against women in the “skilled craft” job category in Santa Clara county, in the respective cases. При рассмотрении дела Sheet Metal Workers, Paradise and Johnson были приняты все три программы позитивных действий, поскольку их цель заключалась в исправлении ситуации, связанной с осуществлявшейся в прошлом практикой международной дискриминации в отношении, соответственно, афро-американского населения со стороны нью-йоркского профсоюза работников металлургической промышленности, органов полиции Алабамы, а также в отношении женщин " квалифицированной категории " в округе Санта-Клара.
In determining the two surface areas Si and Se, structural peculiarities and surface irregularities of the body, such as chamfers, wheel-arches and similar features, shall be taken into account and shall be noted under the appropriate heading in test reports; however, if the body is covered with corrugated sheet metal the area considered shall be that of the plane surface occupied, not that of the developed corrugated surface. Определение обеих поверхностей Si и Sе осуществляется с учетом особенностей конструкции кузова или неровностей поверхности, таких как фаски, надколенные дуги и аналогичные элементы, и эти особенности или неровности учитываются и отмечаются в соответствующей рубрике протоколов испытаний; однако, если кузов имеет покрытие типа гофрированного листа, то искомой поверхностью является прямая поверхность этого покрытия, а не ее развертка.
What we can see here is the metal sheet, this time connected to a sound driver and being fed by a frequency generator. Как мы видим, это металлическая пластина, на этот раз соединенная с динамиком, подключённым к генератору частоты.
Crouching behind soggy sandbags, below a corrugated metal sheet that provides little cover, Nazha scours the land beyond the ruined church. Скрючившись за промокшими мешками с песком под ненадежной защитой из листа гофрированного металла, Нажа всматривается вдаль за руинами церкви.
There, under that metal sheet there. Здесь, под этим металлическим листом.
Iron is the most useful metal. Железо - самый широко используемый металл.
Give me a blank sheet of paper. Дай мне чистый лист бумаги.
Is it made of wood or metal? Это сделано из дерева или из металла?
Off balance sheet financial commitments Внебалансовые финансовые обязательства
Os exemplos de uso de palavras em diferentes contextos são dados só para fins linguísticos, ou seja, para estudar o uso de palavras numa língua e as suas traduções para outra. Todos os exemplos são colecionados automaticamente em fontes abertas usando tecnologia de pesquisa de dados bilíngues. Se você encontrar algum erro de ortografia, pontuação ou outro erro no texto original ou na tradução, use a opção "Reportar um erro" ou escreva para nós.

Nesta seção, você pode ver como palavras e expressões são usadas em diferentes contextos usando exemplos de traduções feitas por profissionais. A seção Contextos o ajudará a aprender inglês, alemão, espanhol e outros idiomas. Aqui você pode encontrar exemplos com verbos frasais e idiomas em textos que variam em estilo e tema. Exemplos podem ser classificados por traduções e tópicos.

Aprenda línguas estrangeiras, veja a tradução de milhões de palavras e expressões e use-as em sua comunicação por e-mail.