Translation of "маркировка осевой линии ВПП" to English
Advert
Dictionary translations for "маркировка осевой линии ВПП"
pl.
маркировки осевой линии впп
pl.
маркировки осевой линии впп
Contexts with "маркировка осевой линии впп"
Определить с помощью сферической модели головы диаметром 165 ± 2 мм начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной в 37 Нм вокруг точки R.
Using a 165 ± 2 mm diameter spherical head form, establish the head form initial reference position by applying, perpendicular to the displaced torso line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 37 Nm moment about the R-point.
Определить с помощью сферической модели головы диаметром 165 ± 2 мм начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной 373 Нм вокруг точки R.
Using a 165 ± 2 mm diameter spherical head form, establish the head form initial reference position by applying, perpendicular to the displaced torso line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 373 Nm moment about the R-point.
Поскольку место, имеющееся в обычной рубке судна внутреннего плавания, ограничено и в силу того, что судно, как правило, следует по осевой линии фарватера, отображение предпочтительнее передавать в портретной ориентации.
Because of the limited space available in the typical wheelhouse of an inland vessel and the fact, that a vessel usually follows the fairway-axis, the display shall be installed preferably in the portrait orientation.
Эта фактическая высота измеряется в зоне, ограниченной двумя вертикальными плоскостями, проходящими на расстоянии 85 мм по обе стороны осевой линии, задней поверхностью, которая должна удовлетворять требованию, предъявляемому к заднему расстоянию, и горизонтальной плоскостью, которая используется для измерения высоты подголовника.
This effective height is measured in an area bounded by two vertical planes set at 85 mm on either side of the centreline, the rear surface which complies with the backset requirement, and the horizontal plane used to measure the height of the head restraint.
Определить с помощью сферической модели головы диаметром 165 ± 2 мм начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной 37 Нм вокруг точки R.
Using a 165 ± 2 mm diameter spherical head form, establish the head form initial reference position by applying, perpendicular to the displaced torso line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 37 Nm moment about the R-point.
Examples of word usage in different contexts are provided solely for linguistic purposes, i.e. to study word usage in a sentence in one language and how they can be translated into another. All samples are automatically collected from a variety of publicly available open sources using bilingual search technologies.
If you find a spelling, punctuation or any other error in the original or translation, use the "Report a problem" option or write to us.
If you find a spelling, punctuation or any other error in the original or translation, use the "Report a problem" option or write to us.
Testimonials
Advert