Exemplos de uso de "Centre" em inglês com tradução "ось"

<>
longitudinal distance (l1) from the centre line of front axle расстояние в продольной плоскости (l1) от центровой линии передней оси,
" Illumination axis ", a line segment from the reference centre to the light source. " Ось освещения "- это отрезок прямой, соединяющий исходный центр с источником света.
" Observation axis ", a line segment from the reference centre to the photometer head. " Ось наблюдения "- это отрезок прямой, соединяющий исходный центр с фотометрической головкой.
r = height of wheel centre (on first axle) above the load cell top surface r = высота центральной точки колеса (на первой оси) над поверхностью динамометра.
Annex 3- Lamp surfaces, axis and centre of reference, and angles of geometric visibility Приложение 3- Поверхности фары, исходная ось и исходный центр, углы геометрической видимости
" First axis ", an axis through the reference centre and perpendicular to the observation half-plane. " Первая ось "- это ось, проходящая через исходный центр перпендикулярно полуплоскости наблюдения.
5 Permissible deviation of the filament axis from the cap axis in the light centre = ± 1 mm 5- Допустимое отклонение оси нити накала от оси цоколя в центре источника света составляет ± 1 мм Рис.
5 Permissible deviation of the filament axis from the cap axis in the light centre = ± 1,5 mm 5- Допустимое отклонение оси нити накала от оси цоколя в центре источника света составляет ± 1,5 мм Рис.
11/Dimensions m and n are measured from the reference axis to the centre of the passing-beam filament. 11/Размеры m и n измеряются по направлению от оси отсчета к центру нити накала фары ближнего света.
the centre of the major filament shall not be offset by more than distance " k " from the reference axis. центр основной нити накала не должен смещаться относительно оси отсчета на расстояние, превышающее " k ";
2/The reference axis is perpendicular to the reference plane and passing through the centre of the 19 mm cap diameter. 2/Ось отсчета представляет собой перпендикуляр к плоскости отсчета и проходит через центр диаметра цоколя (19 мм).
2/The reference axis is perpendicular to the reference plane and passing through the centre of the cap ring diameter'M'. 2 Ось отсчета- это перпендикуляр к плоскости отсчета, проходящий через центр кольца цоколя диаметром'M'.
1/Maximum lateral deviation of filament centre from two mutually perpendicular planes both containing the reference axis and one containing axis X-X. 1/Максимальное боковое отклонение центра нити накала относительно двух взаимно перпендикулярных плоскостей, которые проходят через ось отсчета и одна из которых проходит через ось X-X.
2/Maximum lateral deviation of filament centre from two mutually perpendicular planes both containing the reference axis and one containing axis X-X. 2/Максимальное боковое отклонение центра нити накала относительно двух взаимно перпендикулярных плоскостей, проходящих через ось отсчета, одна из которых проходит через ось X-X.
" Reference axis ", a designated line segment originating on the reference centre which is used to describe the angular position of the retro-reflective device. " Исходная ось "- это определенный отрезок прямой, одним из концов которого является исходный центр и который используется для определения угла наклона светоотражающего устройства.
1/Maximum lateral deviation of filament centre from two mutually perpendicular planes both containing the reference axis and one containing the axis of the pins. 1/Максимальное боковое отклонение центра нити накала относительно двух взаимно перпендикулярных плоскостей, которые проходят через ось отсчета и одна из которых проходит через ось цокольных штифтов.
1/Maximum lateral deviation of filament centre from two mutually perpendicular planes both containing the reference axis and one containing the axis of the reference pin. 1 Максимальное боковое отклонение центра нити накала относительно двух взаимно перпендикулярных плоскостей, которые проходят через ось отсчета и одна из которых проходит через ось контрольного штифта.
2/The filament shall be housed in a cylinder 19 mm long co-axial with the filament lamp and placed symmetrically about the filament lamp centre. 2/Нить накала должна находиться внутри коаксиального с осью лампы накаливания цилиндра длиной 19 мм, расположенного симметрично по отношению к середине лампы.
2/Maximum lateral deviation of filament centre from two mutually perpendicular planes both containing the reference axis and one containing the axis through the reference keys. 2/Максимальное боковое отклонение центра нити накала относительно двух взаимно перпендикулярных плоскостей, которые проходят через ось отсчета и одна из которых проходит через ось контрольных выступов.
2/Maximum lateral deviation of filament centre from two mutually perpendicular planes both containing the reference axis and one containing the axis of the reference pin. 2/Максимальное боковое отклонение центра нити накала относительно двух взаимно перпендикулярных плоскостей, которые проходят через ось отсчета и одна из которых проходит через ось контрольного штифта.
Os exemplos de uso de palavras em diferentes contextos são dados só para fins linguísticos, ou seja, para estudar o uso de palavras numa língua e as suas traduções para outra. Todos os exemplos são colecionados automaticamente em fontes abertas usando tecnologia de pesquisa de dados bilíngues. Se você encontrar algum erro de ortografia, pontuação ou outro erro no texto original ou na tradução, use a opção "Reportar um erro" ou escreva para nós.

Nesta seção, você pode ver como palavras e expressões são usadas em diferentes contextos usando exemplos de traduções feitas por profissionais. A seção Contextos o ajudará a aprender inglês, alemão, espanhol e outros idiomas. Aqui você pode encontrar exemplos com verbos frasais e idiomas em textos que variam em estilo e tema. Exemplos podem ser classificados por traduções e tópicos.

Aprenda línguas estrangeiras, veja a tradução de milhões de palavras e expressões e use-as em sua comunicação por e-mail.